Draytek Vigor2920n Betriebsanweisung

Vigor2920 Series User’s Guide x4.12.3 Phone Settings ...

Vigor2920 Series User’s Guide 88Long Preamble This option is to define the length of the sync field in an 802.11 packet. Most modern wireless networ

Vigor2920 Series User’s Guide 89WPA The WPA encrypts each frame transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered

Vigor2920 Series User’s Guide 9033..66..44 AAcccceessss CCoonnttrrooll For additional security of wireless access, the Access Control facility all

Vigor2920 Series User’s Guide 91OK Click it to save the access control list. Clear All Clean all entries in the MAC address list. 33..66..55 SStta

Vigor2920 Series User’s Guide 9233..77..11 UUSSBB GGeenneerraall SSeettttiinnggss This page will determine the number of concurrent FTP connectio

Vigor2920 Series User’s Guide 93can have as many as 15 characters and the host name can have as many as 23 characters. Both them cannot contain any o

Vigor2920 Series User’s Guide 94accessing into USB storage disk. Note: “Admin” could not be typed here as username, for the word is specified for acc

Vigor2920 Series User’s Guide 9533..77..33 FFiillee EExxpplloorreerr File Explorer offers an easy way for users to view and manage the content of

Vigor2920 Series User’s Guide 96Free Capacity It displays the free space of the USB storage disk. Click Refresh at any time to get new status for fre

Vigor2920 Series User’s Guide 97Firmware Version Display the firmware version of the router. Build Date/Time Display the date and time of the current

Vigor2920 Series User’s Guide xi5.8 Creating an Account for MyVigor ...

Vigor2920 Series User’s Guide 98New Password Type in new password in this field. Confirm Password Type in the new password again. When you click OK

Vigor2920 Series User’s Guide 9933..88..44 RReebboooott SSyysstteemm The Web Configurator may be used to restart your router for using current con

Vigor2920 Series User’s Guide 10033..88..66 AAccttiivvaattiioonn There are three ways to activate WCF on vigor router, using Service Activation Wiz

Vigor2920 Series User’s Guide 101 33..99 DDiiaaggnnoossttiiccss Diagnostic Tools provide a useful way to view or diagnose the status of your Vigor

Vigor2920 Series User’s Guide 10233..99..22 TTrraaffffiicc GGrraapphh Click Diagnostics and click Traffic Graph to pen the web page. Choose WAN1/W

Vigor2920 Series User’s Guide 10333..99..33 PPiinngg DDiiaaggnnoossiiss Click Diagnostics and click Ping Diagnosis to pen the web page. Ping

Vigor2920 Series User’s Guide 10433..99..44 TTrraaccee RRoouuttee Click Diagnostics and click Trace Route to open the web page. This page allows y

Vigor2920 Series User’s Guide 1054 AAddmmiinn MMooddee OOppeerraattiioonn This chapter will guide users to execute advanced (full) configuration

Vigor2920 Series User’s Guide 106From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 WWhhaatt aarr

Vigor2920 Series User’s Guide 107Therefore, when WAN1/WAN2 is not available, the router will use 3.5G for supporting automatically. The supported 3G

Vigor2920 Series User’s Guide 108Physical Mode / Type Display the physical mode and physical type of such WAN interface. Line Speed Display the dow

Vigor2920 Series User’s Guide 109VLAN Tag insertion Enable – Enable the function of VLAN with tag. The router will add specific VLAN number to all

Vigor2920 Series User’s Guide 110To use 3G network connection through 3G USB Modem, please configure WAN3 interface. Enable Choose Yes to invoke the

Vigor2920 Series User’s Guide 111single WAN. When any WAN disconnect – Such backup WAN will be activated when any master WAN interface disconnects.

Vigor2920 Series User’s Guide 112 DDeettaaiillss PPaaggee ffoorr PPPPPPooEE iinn WWAANN11//WWAANN22 To choose PPPoE as the accessing protocol o

Vigor2920 Series User’s Guide 1131442. PPP/MP Setup PPP Authentication – Select PAP only or PAP or CHAP for PPP. If you want to connect to Internet a

Vigor2920 Series User’s Guide 114To use Static or Dynamic IP as the accessing protocol of the internet, please choose Static or Dynamic IP mode from

Vigor2920 Series User’s Guide 115information. Click Enable RIP for activating this function. WAN IP Network Settings This group allows you to obtain

Vigor2920 Series User’s Guide 116DDeettaaiillss PPaaggee ffoorr PPPPTTPP//LL22TTPP iinn WWAANN11//WWAANN22 To use PPTP/L2TP as the accessing pr

Vigor2920 Series User’s Guide 117whenever you request. In this case, you can fill in this IP address in the Fixed IP field. Please contact your ISP b

Vigor2920 Series User’s Guide 11 PPrreeffaaccee Vigor2920 series is a broadband router. It integrates IP layer QoS, NAT session/bandwidth managemen

Vigor2920 Series User’s Guide 118 Enable / Disable Click Enable for activating this function. If you click Disable, this function will be closed and

Vigor2920 Series User’s Guide 119Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection. Ping IP – If you choose Ping De

Vigor2920 Series User’s Guide 120Dest IP End Displays the IP address for the end of the destination IP. Dest Port Start Displays the IP address for t

Vigor2920 Series User’s Guide 121Dest Port Start Type the destination port start for the destination IP. Dest Port End Type the destination port end

Vigor2920 Series User’s Guide 122WAN link for Channel 5, 6 and 7 are provided for router-borne application such as TR-069. The settings must be appli

Vigor2920 Series User’s Guide 123BBrriiddggee General page lets you set the first channel. As to set the third channel, please click the Bridge tab

Vigor2920 Series User’s Guide 12444..22 LLAANN Local Area Network (LAN) is a group of subnets regulated and ruled by router. The design of network

Vigor2920 Series User’s Guide 125 WWhhaatt iiss RRoouuttiinngg IInnffoorrmmaattiioonn PPrroottooccooll ((RRIIPP)) Vigor router will exchange ro

Vigor2920 Series User’s Guide 126 44..22..22 GGeenneerraall SSeettuupp This page provides you the general settings for LAN. Click LAN to open the

Vigor2920 Series User’s Guide 127 Start IP Address: Enter a value of the IP address pool for the DHCP server to start with when issuing IP addresses

Vigor2920 Series User’s Guide 211..22 LLEEDD IInnddiiccaattoorrss aanndd CCoonnnneeccttoorrss Before you use the Vigor router, please get acquai

Vigor2920 Series User’s Guide 128 If you want to use another DHCP server in the network other than the Vigor Router’s, you can let Relay Agent help

Vigor2920 Series User’s Guide 129There are two common scenarios of LAN settings that stated in Chapter 4. For the configuration examples, please refe

Vigor2920 Series User’s Guide 130 1. Go to LAN page and click General Setup, select 1st Subnet as the RIP Protocol Control. Then click the OK butto

Vigor2920 Series User’s Guide 131 4. Go to Diagnostics and choose Routing Table to verify current routing table.

Vigor2920 Series User’s Guide 13244..22..44 VVLLAANN Virtual LAN function provides you a very convenient way to manage hosts by grouping them based

Vigor2920 Series User’s Guide 133 To remove VLAN, uncheck the needed box and click OK to save the results. 44..22..55 BBiinndd IIPP ttoo MMAACC

Vigor2920 Series User’s Guide 134Strict Bind Click this radio button to block the connection of the IP/MAC which is not listed in IP Bind List. ARP T

Vigor2920 Series User’s Guide 135On NAT page, you will see the private IP address defined in RFC-1918. Usually we use the 192.168.1.0/24 subnet for t

Vigor2920 Series User’s Guide 136 Press any number under Index to access into next page for configuring port redirection. Enable Check this box to

Vigor2920 Series User’s Guide 137number on the first box. The second one will be assigned automatically later. Private IP Specify the private IP add

Vigor2920 Series User’s Guide 3 Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blink

Vigor2920 Series User’s Guide 138 The security properties of NAT are somewhat bypassed if you set up DMZ host. We suggest you to add additional filte

Vigor2920 Series User’s Guide 139 Enable Check to enable the DMZ Host function. Private IP Enter the private IP address of the DMZ host, or click Cho

Vigor2920 Series User’s Guide 140 Index Indicate the relative number for the particular entry that you want to offer service in a local host. You sho

Vigor2920 Series User’s Guide 141setting is available when WAN IP Alias is configured. Local Computer Enter the private IP address of the local host

Vigor2920 Series User’s Guide 14244..44 FFiirreewwaallll 44..44..11 BBaassiiccss ffoorr FFiirreewwaallll While the broadband users demand more

Vigor2920 Series User’s Guide 143 SSttaatteeffuull PPaacckkeett IInnssppeeccttiioonn ((SSPPII)) Stateful inspection is a firewall architecture t

Vigor2920 Series User’s Guide 14444..44..22 GGeenneerraall SSeettuupp General Setup allows you to adjust settings of IP Filter and common options.

Vigor2920 Series User’s Guide 145Such page allows you to choose filtering profiles including QoS, Load-Balance policy, WCF, APP Enforcement, URL Cont

Vigor2920 Series User’s Guide 146 User Management Such item is available only when Rule-Based is selected in User Management>>General Setup. T

Vigor2920 Series User’s Guide 147 Codepage - This function is used to compare the characters among different languages. Choose correct codepage can

Vigor2920 Series User’s Guide 411..22..22 FFoorr VViiggoorr22992200nn LED Status Explanation Blinking The router is powered on and running nor

Vigor2920 Series User’s Guide 148 To edit or add a filter, click on the set number to edit the individual set. The following page will be shown. Each

Vigor2920 Series User’s Guide 149 Check to enable the Filter Rule Check this box to enable the filter rule. Comments Enter filter set comments/descri

Vigor2920 Series User’s Guide 150 To set the IP address manually, please choose Any Address/Single Address/Range Address/Subnet Address as the Addr

Vigor2920 Series User’s Guide 151 Protocol - Specify the protocol(s) which this filter rule will apply to. Source/Destination Port – (=) – when t

Vigor2920 Series User’s Guide 152configured in IP Object for Source IP and Destination IP be bound for applying such filter rule. No-Strict - no limi

Vigor2920 Series User’s Guide 153Content Filter web page first. Or choose [Create New] from the drop down list in this page to create a new profile.

Vigor2920 Series User’s Guide 154will be. However, if the network is not stable, small value will be proper. Session timeout–Setting timeout for sess

Vigor2920 Series User’s Guide 155EExxaammppllee As stated before, all the traffic will be separated and arbitrated using on of two IP filters: call

Vigor2920 Series User’s Guide 15644..44..44 DDooSS DDeeffeennssee As a sub-functionality of IP Filter/Firewall, there are 15 types of detect/ defe

Vigor2920 Series User’s Guide 157coming from the Internet. The default setting for threshold and timeout are 50 packets per second and 10 seconds, re

Vigor2920 Series User’s Guide 5 Interface Description Wireless LAN ON/OFF/WPS Press "Wireless LAN ON/OFF/WPS" button once to wait fo

Vigor2920 Series User’s Guide 158once they re-construct the packets. The Vigor routers will block any packets realizing this attacking activity. Bloc

Vigor2920 Series User’s Guide 15944..55 UUsseerr MMaannaaggeemmeenntt User Management is a security feature which disallows any IP traffic (except

Vigor2920 Series User’s Guide 16044..55..11 GGeenneerraall SSeettuupp General Setup can determine the standard (rule-based or user-based) for the

Vigor2920 Series User’s Guide 16144..55..22 UUsseerr PPrrooffiillee This page allows you to set customized profiles (up to 200) which will be appl

Vigor2920 Series User’s Guide 162user tries to access Internet through this router, an authentication step must be performed first. The user has to t

Vigor2920 Series User’s Guide 163Authentication external service such as LDAP server or Radius server. If LDAP or Radius is selected here, it is not

Vigor2920 Series User’s Guide 164Setup All the schedules can be set previously in Application >> Schedule web page and you can use the number t

Vigor2920 Series User’s Guide 16544..55..44 UUsseerr OOnnlliinnee SSttaattuuss This page displays the user(s) connected to the router and refresh

Vigor2920 Series User’s Guide 16644..66 OObbjjeeccttss SSeettttiinnggss For IPs in a range and service ports in a limited range usually will be ap

Vigor2920 Series User’s Guide 167 Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose a proper interface. For e

Vigor2920 Series User’s Guide 611..22..33 FFoorr VViiggoorr22992200VVnn LED Status Explanation Blinking The router is powered on and running n

Vigor2920 Series User’s Guide 168Subnet Mask Type the subnet mask if the Subnet Address type is selected. Invert Selection If it is checked, all the

Vigor2920 Series User’s Guide 169 Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose WAN, LAN or Any to display a

Vigor2920 Series User’s Guide 17044..66..33 SSeerrvviiccee TTyyppee OObbjjeecctt You can set up to 96 sets of Service Type Objects with differe

Vigor2920 Series User’s Guide 171(=) – when the first and last value are the same, it indicates one port; when the first and last values are differen

Vigor2920 Series User’s Guide 172Click the number under Index column for settings in detail. Name Type a name for this profile. Available Service Ty

Vigor2920 Series User’s Guide 173Click the number under Index column for setting in detail. Name Type a name for this profile, e.g., game. Contents

Vigor2920 Series User’s Guide 174 Click the number under Index column for setting in detail. Name Type a name for this group. Available Keyword Obje

Vigor2920 Series User’s Guide 175 Profile Name Type a name for this profile. Type a name for such profile and check all the items of file extension t

Vigor2920 Series User’s Guide 17644..77 CCSSMM PPrrooffiillee CCoonntteenntt SSeeccuurriittyy MMaannaaggeemmeenntt ((CCSSMM)) CSM is an abbrev

Vigor2920 Series User’s Guide 177 44..77..11 AAPPPP EEnnffoorrcceemmeenntt PPrrooffiillee You can define policy profiles for IM (Instant Messeng

Vigor2920 Series User’s Guide 7 Interface Description Wireless LAN ON/OFF/WPS Press "Wireless LAN ON/OFF/WPS" button once to wait fo

Vigor2920 Series User’s Guide 178 Profile Name Type a name for the CSM profile. Select All Click it to choose all of the items in this page. Clear Al

Vigor2920 Series User’s Guide 179 The items categorized under Protocol. The items categorized under Misc -----

Vigor2920 Series User’s Guide 180 44..77..22 UURRLL CCoonntteenntt FFiilltteerr PPrrooffiillee To provide an appropriate cyberspace to users, V

Vigor2920 Series User’s Guide 181Also the Vigor router will discard any request that tries to retrieve the malicious code. Click CSM and click URL Co

Vigor2920 Series User’s Guide 182Feature below. When you choose this setting, both configuration set in this page for URL Access Control and Web Feat

Vigor2920 Series User’s Guide 183If the web pages do not match with the keyword set here, it will be processed with reverse action. Group/Object Sel

Vigor2920 Series User’s Guide 184Proxy - Check the box to reject any proxy transmission. To control efficiently the limited-bandwidth usage, it will

Vigor2920 Series User’s Guide 185 Activate Click it to access into MyVigor for activating WCF service. Setup Query Server It is recommended for you t

Vigor2920 Series User’s Guide 186matches, the page will be retrieved quickly. Such item can provide URL matching with the fastest rate. L1+L2 Cache –

Vigor2920 Series User’s Guide 187Pass - allow accessing into the corresponding webpage with the characters listed on Group/Object Selections. If the

Vigor2920 Series User’s Guide ii

Vigor2920 Series User’s Guide 811..33 HHaarrddwwaarree IInnssttaallllaattiioonn Before starting to configure the router, you have to connect you

Vigor2920 Series User’s Guide 188 To activate the function of limit session, simply click Enable and set the default session limit. Enable Click th

Vigor2920 Series User’s Guide 189maximum number of Internet sessions permitted. Index (1-15) in Schedule Setup You can type in four sets of time sche

Vigor2920 Series User’s Guide 190make the best utilization of available bandwidth. using according to the bandwidth limit set by the user. If yes, th

Vigor2920 Series User’s Guide 191The basic QoS implementation in Vigor routers is to classify and schedule packets based on the service type informat

Vigor2920 Series User’s Guide 192This page displays the QoS settings result of the WAN interface. Click the Setup link to access into next page for t

Vigor2920 Series User’s Guide 193 Enable the QoS Control The factory default for this setting is checked. Please also define which traffic the QoS Co

Vigor2920 Series User’s Guide 194Outbound TCP ACK Prioritize The difference in bandwidth between download and upload are great in ADSL2+ environment.

Vigor2920 Series User’s Guide 195For adding a new rule, click Add to open the following page. ACT Check this box to invoke these settings. Local A

Vigor2920 Series User’s Guide 196 EEddiitt tthhee SSeerrvviiccee TTyyppee ffoorr CCllaassss RRuullee To add a new service type, edit or delete

Vigor2920 Series User’s Guide 197For adding a new service type, click Add to open the following page. Service Name Type in a new service for your

Vigor2920 Series User’s Guide 911..44 PPrriinntteerr IInnssttaallllaattiioonn You can install a printer onto the router for sharing printing. All

Vigor2920 Series User’s Guide 19844..99 AApppplliiccaattiioonnss Below shows the menu items for Applications. 44..99..11 DDyynnaammiicc DDNNSS

Vigor2920 Series User’s Guide 199page of DDNS setup to set account(s). WAN Interface Display the WAN interface used. Domain Name Display the domain n

Vigor2920 Series User’s Guide 200Domain Name Type in one domain name that you applied previously. Use the drop down list to choose the desired domain

Vigor2920 Series User’s Guide 201You can set up to 15 schedules. Then you can apply them to your Internet Access or VPN and Remote Access >> LA

Vigor2920 Series User’s Guide 202Office Hour: (Force On) Mon - Sun 9:00 am to 6:00 pm 1. Make sure the PPPoE connection and Time Setup is workin

Vigor2920 Series User’s Guide 20344..99..44 UUPPnnPP The UPnP (Universal Plug and Play) protocol is supported to bring to network connected devices

Vigor2920 Series User’s Guide 204The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Enabling firewall app

Vigor2920 Series User’s Guide 20544..99..55 IIGGMMPP IGMP is the abbreviation of Internet Group Management Protocol. It is a communication protocol

Vigor2920 Series User’s Guide 20644..99..66 WWaakkee oonn LLAANN A PC client on LAN can be woken up by the router it connects. When a user wants

Vigor2920 Series User’s Guide 20744..1100 VVPPNN aanndd RReemmoottee AAcccceessss A Virtual Private Network (VPN) is the extension of a private

Vigor2920 Series User’s Guide 10 4. Click Local printer attached to this computer and click Next. 5. In this dialog, choose Create a new port

Vigor2920 Series User’s Guide 208 When you finish the mode and profile selection, please click Next to open the following page. In this page, yo

Vigor2920 Series User’s Guide 209 z When you choose IPSec, you will see the following graphic:

Vigor2920 Series User’s Guide 210z When you choose L2TP, you will see the following graphic: z When you choose L2TP over IPSec (Nice to Have) or

Vigor2920 Series User’s Guide 211 WAN1 First - While connecting, the router will use WAN1 as the first channel for VPN connection. If WAN1 fails, t

Vigor2920 Series User’s Guide 212User Name This field is used to authenticate for connection when you select PPTP or L2TP with or without IPSec polic

Vigor2920 Series User’s Guide 21344..1100..22 VVPPNN SSeerrvveerr WWiizzaarrdd Such wizard is used to configure VPN settings for VPN server. Such

Vigor2920 Series User’s Guide 214 Please choose a Dial-in User Accounts This item is available when you choose Remote Dial-in User (Teleworker) as

Vigor2920 Series User’s Guide 215z When you check PPTP, you will see the following graphic: z When you check PPTP/IPSec/L2TP (three types) or PPTP

Vigor2920 Series User’s Guide 216z When you check IPSec, you will see the following graphic: Profile Name Type a name for such profile. The length

Vigor2920 Series User’s Guide 217After finishing the configuration, please click Next. The confirmation page will be shown as follows. If there is no

Vigor2920 Series User’s Guide 116. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type I

Vigor2920 Series User’s Guide 21844..1100..44 PPPPPP GGeenneerraall SSeettuupp This submenu only applies to PPP-related VPN connections, such as

Vigor2920 Series User’s Guide 219should choose an IP address from the local private network. For example, if the local private network is 192.168.1

Vigor2920 Series User’s Guide 220Pre-Shared Key -Currently only support Pre-Shared Key authentication. Pre-Shared Key- Specify a key for IKE authenti

Vigor2920 Series User’s Guide 221 Profile Name Type the name of the profile. Accept Any Peer ID Click to accept any peer regardless of its identity.

Vigor2920 Series User’s Guide 222 Set to Factory Default Click to clear all indexes. Index Click the number below Index to access into the setting pa

Vigor2920 Series User’s Guide 223 User account and Authentication Enable this account - Check the box to enable this function. Idle Timeout- If the d

Vigor2920 Series User’s Guide 224 Netbios Naming Packet Pass – Click it to have an inquiry for data transmission between the hosts located on both

Vigor2920 Series User’s Guide 225be used only in IKE aggressive mode. 44..1100..88 LLAANN ttoo LLAANN Here you can manage LAN-to-LAN connections

Vigor2920 Series User’s Guide 226 Profile Name Specify a name for the profile of the LAN-to-LAN connection. Enable this profile Check here to activat

Vigor2920 Series User’s Guide 227connection. Netbios Naming Packet Pass – click it to have an inquiry for data transmission between the hosts locate

Vigor2920 Series User’s Guide 129. Now, your system will ask you to choose right name of the printer that you installed onto the router. Such step c

Vigor2920 Series User’s Guide 228 L2TP with IPSec Policy - Build a L2TP VPN connection through the Internet. You can select to use L2TP alone or with

Vigor2920 Series User’s Guide 229apply MD5 or SHA-1 authentication algorithm. Advanced Specify mode, proposal and key life of each IKE phase, Gateway

Vigor2920 Series User’s Guide 230 Allowed Dial-In Type Determine the dial-in connection with different types. PPTP - Allow the remote dial-in user to

Vigor2920 Series User’s Guide 231If you uncheck the checkbox, the connection type you select above will apply the authentication methods and security

Vigor2920 Series User’s Guide 232Network Mask configuration. You can modify the settings if required. More Add a static route to direct all traffic d

Vigor2920 Series User’s Guide 23344..1100..99 CCoonnnneeccttiioonn MMaannaaggeemmeenntt You can find the summary table of all VPN connections. You

Vigor2920 Series User’s Guide 23444..1111 CCeerrttiiffiiccaattee MMaannaaggeemmeenntt A digital certificate works as an electronic ID, which is is

Vigor2920 Series User’s Guide 235 Type in all the information that the window requests. Then click Generate again. Import Click this button to impo

Vigor2920 Series User’s Guide 23644..1111..22 TTrruusstteedd CCAA CCeerrttiiffiiccaattee Trusted CA certificate lists three sets of trusted CA ce

Vigor2920 Series User’s Guide 23744..1111..33 CCeerrttiiffiiccaattee BBaacckkuupp Local certificate and Trusted CA certificate for this router can

Vigor2920 Series User’s Guide 13The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor

Vigor2920 Series User’s Guide 238z Calling via SIP Servers First, the Vigor V models of yours will have to register to a SIP Registrar by sending

Vigor2920 Series User’s Guide 23944..1122..11 DDiiaallPPllaann This page allows you to set phone book and digit map for the VoIP function. Click th

Vigor2920 Series User’s Guide 240in the phonebook for you to store all your friends and family members’ SIP addresses. Loop through and Backup Phone

Vigor2920 Series User’s Guide 241Loop through Choose PSTN to enable loop through function. Backup Phone Number When the VoIP phone is obstructs o

Vigor2920 Series User’s Guide 242Strip - When you choose this mode, the OP number will be deleted by the prefix number for calling out through the sp

Vigor2920 Series User’s Guide 243 Click any index number to display the dial plan setup page. Enable Click this to enable this entry. Call Direct

Vigor2920 Series User’s Guide 244Specific Number barring Type. Route All means all the phone calls will be blocked with such mechanism. Index (1-15

Vigor2920 Series User’s Guide 245 RReeggiioonnaall This page allows you to process incoming or outgoing phone calls by regional. Default values (com

Vigor2920 Series User’s Guide 246Call Forward [Deact] Dial the number typed in this field to release the call forward function. Call Forward [Busy][

Vigor2920 Series User’s Guide 247 Then, check the Enable box to make the PSTN number available for dial whenever you need.

Vigor2920 Series User’s Guide 14 This page is left blank.

Vigor2920 Series User’s Guide 24844..1122..22 SSIIPP AAccccoouunnttss In this section, you set up your own SIP settings. When you apply for an acc

Vigor2920 Series User’s Guide 249lines with numbers (30 – 39) offered for ISDN-S0. You can specify any one of them as ring port for specified SIP acc

Vigor2920 Series User’s Guide 250SIP Port Set the port number for sending/receiving SIP message for building a session. The default value is 5060. Y

Vigor2920 Series User’s Guide 25144..1122..33 PPhhoonnee SSeettttiinnggss This page allows user to set phone settings for Phone 1 and Phone 2 resp

Vigor2920 Series User’s Guide 252down list to choose any one of them.

Vigor2920 Series User’s Guide 253DDeettaaiilleedd SSeettttiinnggss ffoorr PPhhoonnee PPoorrtt Click the number link for Phone port, you can acce

Vigor2920 Series User’s Guide 254Index (1-60) in Phone Book - Enter the index of phone book profiles. Refer to section DialPlan – Phone Book for deta

Vigor2920 Series User’s Guide 255In addition, you can press the Advanced button to configure tone settings, volume gain, MISC and DTMF mode. Advanced

Vigor2920 Series User’s Guide 256 Also, you can specify each field for your necessity. It is recommended for you to use the default settings for VoIP

Vigor2920 Series User’s Guide 25744..1122..44 SSttaattuuss From this page, you can find codec, connection and other important call status for eac

Vigor2920 Series User’s Guide 152 CCoonnffiigguurriinngg BBaassiicc SSeettttiinnggss For using the router properly, it is necessary for you to ch

Vigor2920 Series User’s Guide 258Rx Pkts Total number of received voice packets during this connection session. Rx Losts Total number of lost packe

Vigor2920 Series User’s Guide 259 MMuullttiippllee SSSSIIDDss Vigor router supports four SSID settings for wireless connections. Each SSID can be d

Vigor2920 Series User’s Guide 260the confidential information leakage. For a more flexible deployment, you may add filters of MAC addresses to isolat

Vigor2920 Series User’s Guide 261Enable Wireless LAN Check the box to enable wireless function. Mode At present, the router can connect to 11n Only,

Vigor2920 Series User’s Guide 262 Long Preamble This option is to define the length of the sync field in an 802.11 packet. Most modern wireless netw

Vigor2920 Series User’s Guide 263connection. Upload – Check Enable and type the transmitting rate for data upload. Default value is 30,000 kbps. Down

Vigor2920 Series User’s Guide 264 Note: You should also set RADIUS Server simultaneously if 802.1x mode is selected. Disable - Turn off the encrypt

Vigor2920 Series User’s Guide 2650x4142434445.) 128-Bit - For 128 bits WEP key, either 13 ASCII characters, such as ABCDEFGHIJKLM (or 26 hexadecimal

Vigor2920 Series User’s Guide 266Apply SSID After entering the client’s MAC address, check the box of the SSIDs desired to insert this MAC address in

Vigor2920 Series User’s Guide 26744..1133..55 WWPPSS WPS (Wi-Fi Protected Setup) provides easy procedure to make network connection between wireles

Vigor2920 Series User’s Guide 165. The web page can be logged out according to the chosen condition. The default setting is Auto Logout, which means

Vigor2920 Series User’s Guide 268z If you want to use PIN code, you have to know the PIN code specified in wireless client. Then provide the PIN cod

Vigor2920 Series User’s Guide 269SSID Display the SSID1 of the router. WPS is supported by SSID1 only. Authentication Mode Display current authentica

Vigor2920 Series User’s Guide 270The application for the WDS-Repeater mode is depicted as below: The major difference between these two modes is t

Vigor2920 Series User’s Guide 271 Mode Choose the mode for WDS setting. Disable mode will not invoke any WDS setting. Bridge mode is designed to fulf

Vigor2920 Series User’s Guide 272Bridge If you choose Bridge as the connecting mode, please type in the peer MAC address in these fields. Four peer M

Vigor2920 Series User’s Guide 273sizes. It is used for improving MAC layer’s performance for some brand’s clients. The default setting is Enable. 44.

Vigor2920 Series User’s Guide 274categories must be greater. Txop It means transmission opportunity. For WMM categories of AC_VI and AC_VO that need

Vigor2920 Series User’s Guide 275shown on the box above this button. Statistics It displays the statistics for the channels used by APs. Add to If

Vigor2920 Series User’s Guide 276Add Click this button to add current typed MAC address into Access Control. 44..1144 UUSSBB AApppplliiccaattiioonn

Vigor2920 Series User’s Guide 277 Default Charset is for English based file name. For Simplified Chinese file/directory names, please choose GB2312

Vigor2920 Series User’s Guide 17 Main screen for user mode operation (simple configuration) Note: The home page will change slightly in accordance wi

Vigor2920 Series User’s Guide 278 FTP/Samba User Enable – Click this button to activate this profile (account) for FTP service or Samba User service.

Vigor2920 Series User’s Guide 279 Access Rule It determines the authority for such profile. Any user, who uses such profile for accessing into USB s

Vigor2920 Series User’s Guide 280for other user through FTP. 44..1144..44 UUSSBB DDiisskk SSttaattuuss This page is to monitor the status for th

Vigor2920 Series User’s Guide 28144..1155 SSyysstteemm MMaaiinntteennaannccee For the system setup, there are several items that you have to know

Vigor2920 Series User’s Guide 282DNS Display the assigned IP address of the primary DNS. Wireless LAN------- MAC Address Display the MAC address of

Vigor2920 Series User’s Guide 283ACS Server On Choose the interface for the router connecting to ACS server. ACS Server URL/Username/Password – Such

Vigor2920 Series User’s Guide 28444..1155..44 UUsseerr PPaasssswwoorrdd This page allows you to set new password for user operation. Old Password

Vigor2920 Series User’s Guide 2852. Click Backup button to get into the following dialog. Click Save button to open another dialog for saving config

Vigor2920 Series User’s Guide 286RReessttoorree CCoonnffiigguurraattiioonn 1. Go to System Maintenance >> Configuration Backup. The followin

Vigor2920 Series User’s Guide 287disk. Router Name Display the name for such router configured in System Maintenance>>Management. If there is n

Vigor2920 Series User’s Guide iii Vigor2920 Series Dual-WAN Security Router User’s Guide Version: 1.1 Firmware Version: V3.3.6 D

Vigor2920 Series User’s Guide 18 22..44 QQuuiicckk SSttaarrtt WWiizzaarrdd Notice: Quick Start Wizard for user mode operation is the same as f

Vigor2920 Series User’s Guide 288 44..1155..77 TTiimmee aanndd DDaattee It allows you to specify where the time of the router should be inquired

Vigor2920 Series User’s Guide 289Interval Click OK to save these settings. 44..1155..88 MMaannaaggeemmeenntt This page allows you to manage the set

Vigor2920 Series User’s Guide 290HTTP and FTP servers. Enable SNMP Agent Check it to enable this function. Get Community Set the name for getting com

Vigor2920 Series User’s Guide 29144..1155..1100 FFiirrmmwwaarree UUppggrraaddee Before upgrading your router firmware, you need to install the R

Vigor2920 Series User’s Guide 29244..1155..1111 AAccttiivvaattiioonn There are three ways to activate WCF on vigor router, using Service Activation

Vigor2920 Series User’s Guide 293Below shows the successful activation of Web Content Filter: 44..1166 DDiiaaggnnoossttiiccss Diagnostic Tools pr

Vigor2920 Series User’s Guide 294 Decoded Format It shows the source IP address (local), destination IP (remote) address, the protocol and length of

Vigor2920 Series User’s Guide 29544..1166..33 AARRPP CCaacchhee TTaabbllee Click Diagnostics and click ARP Cache Table to view the content of the

Vigor2920 Series User’s Guide 296Leased Time It displays the leased time of the specified PC. HOST ID It displays the host ID name of the specified P

Vigor2920 Series User’s Guide 297 Enable Data Flow Monitor Check this box to enable this function. Refresh Seconds Use the drop down list to choose t

Vigor2920 Series User’s Guide 19On the next page as shown below, please select the WAN interface that you use. If Ethernet interface is used, please

Vigor2920 Series User’s Guide 298 Unblock – the device with the IP address will be blocked in five minutes. The remaining time will be shown on the s

Vigor2920 Series User’s Guide 299 The horizontal axis represents time. Yet the vertical axis has different meanings. For WAN1/WAN2/WAN3 Bandwidth cha

Vigor2920 Series User’s Guide 300displayed on the screen. Clear Click this link to remove the result on the window. 44..1166..99 TTrraaccee RRoouu

Vigor2920 Series User’s Guide 3015 AApppplliiccaattiioonn aanndd EExxaammpplleess 55..11 CCrreeaattee aa LLAANN--ttoo--LLAANN CCoonnnneecctti

Vigor2920 Series User’s Guide 302general settings in IPSec General Setup, such as the pre-shared key that both parties have known. 3. Go to LAN-to

Vigor2920 Series User’s Guide 3035. Set Dial-Out Settings as shown below to dial to connect to Router B aggressively with the selected Dial-Out meth

Vigor2920 Series User’s Guide 3046. Set Dial-In settings to as shown below to allow Router B dial-in to build VPN connection. If an IPSec-based ser

Vigor2920 Series User’s Guide 3057. At last, set the remote network IP/subnet in TCP/IP Network Settings so that Router A can direct the packets des

Vigor2920 Series User’s Guide 3063. Go to LAN-to-LAN. Click on one index number to edit a profile. 4. Set Common Settings as shown below. You shoul

Vigor2920 Series User’s Guide 307If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, PPP A

Vigor2920 Series User’s Guide 2022..44..11..11 PPPPPPooEE PPPoE stands for Point-to-Point Protocol over Ethernet. It relies on two widely accepted

Vigor2920 Series User’s Guide 308If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, and V

Vigor2920 Series User’s Guide 30955..22 CCrreeaattee aa RReemmoottee DDiiaall--iinn UUsseerr CCoonnnneeccttiioonn BBeettwweeeenn tthhee TTee

Vigor2920 Series User’s Guide 310 3. Go to Remote Dial-In User. Click on one index number to edit a profile. 4. Set Dial-In settings to as shown b

Vigor2920 Series User’s Guide 311If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, and V

Vigor2920 Series User’s Guide 312 You may further specify the method you use to get IP, the security method, and authentication method. If the Pre-S

Vigor2920 Series User’s Guide 313 4. Click Connect button to build connection. When the connection is successful, you will find a green light on th

Vigor2920 Series User’s Guide 314 3. Set Inbound/Outbound bandwidth. Note: The rate of outbound/inbound must be smaller than the real bandwidth to

Vigor2920 Series User’s Guide 3155. For this index, the user will set reserved bandwidth (e.g., 25%) for E-mail using protocol POP3 and SMTP. 6.

Vigor2920 Series User’s Guide 3168. Check Enable UDP Bandwidth Control on the bottom to prevent enormous UDP traffic of influent other application.

Vigor2920 Series User’s Guide 317 12. Then click Edit of Local Address to set a worker’s subnet address. Click Edit of Remote Address to set headqua

Vigor2920 Series User’s Guide 21Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be

Vigor2920 Series User’s Guide 318 To use another DHCP server in the network rather than the built-in one of Vigor Router, you have to change the sett

Vigor2920 Series User’s Guide 319 55..55 UUppggrraaddee FFiirrmmwwaarree ffoorr YYoouurr RRoouutteerr Before upgrading your router firmware, y

Vigor2920 Series User’s Guide 3203. Access into Support >> Downloads. Please find out Utility menu and click it. 4. Click on the link of Rou

Vigor2920 Series User’s Guide 321custom settings to default settings). Choose any one of them that you need. 10. Click Send. 11. Now the firmware

Vigor2920 Series User’s Guide 32255..66 RReeqquueesstt aa cceerrttiiffiiccaattee ffrroomm aa CCAA sseerrvveerr oonn WWiinnddoowwss CCAA SS

Vigor2920 Series User’s Guide 3232. You can click GENERATE button to start to edit a certificate request. Enter the information in the certificate r

Vigor2920 Series User’s Guide 324Select Advanced request. Select Submit a certificate request a base64 encoded PKCS #10 file or a renewal request us

Vigor2920 Series User’s Guide 325you will find the below window showing “------BEGINE CERTIFICATE------...” 6. You may review the detail informat

Vigor2920 Series User’s Guide 32655..77 RReeqquueesstt aa CCAA CCeerrttiiffiiccaattee aanndd SSeett aass TTrruusstteedd oonn WWiinnddoowwss

Vigor2920 Series User’s Guide 3272. In Choose file to download, click CA Certificate Current and Base 64 encoded, and Download CA certificate to sav

Vigor2920 Series User’s Guide 22Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be

Vigor2920 Series User’s Guide 32855..88 CCrreeaattiinngg aann AAccccoouunntt ffoorr MMyyVViiggoorr The website of MyVigor (a server located on

Vigor2920 Series User’s Guide 3292. Click the Activate link. A login page for MyVigor web site will pop up automatically. 3. Click the link of Cre

Vigor2920 Series User’s Guide 3305. Type your personal information in this page and then click Continue. 6. Choose proper selection for your compu

Vigor2920 Series User’s Guide 3317. Now you have created an account successfully. Click START. 8. Check to see the confirmation email with the tit

Vigor2920 Series User’s Guide 33210. When you see the following page, please type in the account and password (that you just created) in the fields o

Vigor2920 Series User’s Guide 3332. Check to confirm that you accept the Agreement and click Accept. 3. Type your personal information in this pag

Vigor2920 Series User’s Guide 3345. Now you have created an account successfully. Click START. 6. Check to see the confirmation email with the tit

Vigor2920 Series User’s Guide 3358. When you see the following page, please type in the account and password (that you just created) in the fields o

Vigor2920 Series User’s Guide 336 This page is left blank.

Vigor2920 Series User’s Guide 337 TTrroouubbllee SShhoooottiinngg situations if you cannot access into the Internet after installing the router an

Vigor2920 Series User’s Guide 23Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be

Vigor2920 Series User’s Guide 33866..22 CChheecckkiinngg IIff tthhee NNeettwwoorrkk CCoonnnneeccttiioonn SSeettttiinnggss oonn YYoouurr CCoo

Vigor2920 Series User’s Guide 3394. Select Obtain an IP address automatically and Obtain DNS server address automatically. FFoorr MMaacc OOSS 1.

Vigor2920 Series User’s Guide 34066..33 PPiinnggiinngg tthhee RRoouutteerr ffrroomm YYoouurr CCoommppuutteerr The default gateway IP address o

Vigor2920 Series User’s Guide 341 66..44 CChheecckkiinngg IIff tthhee IISSPP SSeettttiinnggss aarree OOKK oorr NNoott Open WAN >> In

Vigor2920 Series User’s Guide 342 TTrraannssmmiissssiioonn RRaattee iiss nnoott ffaasstt eennoouugghh Please connect your Notebook with 3G USB

Vigor2920 Series User’s Guide 343 HHaarrddwwaarree RReesseett While the router is running (ACT LED blinking), press the Factory Reset button and ho

Vigor2920 Series User’s Guide 24Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be

Vigor2920 Series User’s Guide 2522..55 SSeerrvviiccee AAccttiivvaattiioonn WWiizzaarrdd Service Activation Wizard can guide you to activate WCF s

Vigor2920 Series User’s Guide 263. In the following page, you can activate the Web content filter services at the same time or individually. When yo

Vigor2920 Series User’s Guide 27Note: The service will be activated and applied as the default rule configured in Firewall>>General Setup. 6.

Vigor2920 Series User’s Guide ivCopyright Information Copyright Declarations Copyright 2010 All rights reserved. This publication contains informati

Vigor2920 Series User’s Guide 28 22..66 OOnnlliinnee SSttaattuuss 22..66..11 PPhhyyssiiccaall CCoonnnneeccttiioonn Such page displays the phys

Vigor2920 Series User’s Guide 29IP Displays the IP address of the WAN interface. GW IP Displays the IP address of the default gateway. TX Packets

Vigor2920 Series User’s Guide 3022..88 SSuuppppoorrtt AArreeaa When you click the menu item under Support Area, you will be guided to visit www.dr

Vigor2920 Series User’s Guide 313 UUsseerr MMooddee OOppeerraattiioonn This chapter will guide users to execute simple configuration through user

Vigor2920 Series User’s Guide 32From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 WWhhaatt aarre

Vigor2920 Series User’s Guide 33Therefore, when WAN1/WAN2 is not available, the router will use 3.5G for supporting automatically. The supported 3G U

Vigor2920 Series User’s Guide 34interface. Active Mode Display whether such WAN interface is used as Active device or backup device. Backup WAN Displ

Vigor2920 Series User’s Guide 35WAN while sending them out. Please type the tag value and specify the priority for the packets sending by WAN1. Dis

Vigor2920 Series User’s Guide 36WWAANN33 wwiitthh UUSSBB To use 3G network connection through 3G USB Modem, please configure WAN3 interface. Enab

Vigor2920 Series User’s Guide 37the WAN interface should play if you want to backup multiple WANs. However, ignore this setting if you want to backup

Vigor2920 Series User’s Guide vEuropean Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Township, HsinCh

Vigor2920 Series User’s Guide 3833..11..33 IInntteerrnneett AAcccceessss For the router supports multi-WAN function, the users can set different W

Vigor2920 Series User’s Guide 39 Enable/Disable Click Enable for activating this function. If you click Disable, this function will be closed and a

Vigor2920 Series User’s Guide 40 WAN IP Alias - If you have multiple public IP addresses and would like to utilize them on the WAN interface, please

Vigor2920 Series User’s Guide 41 Static or Dynamic IP Click Enable for activating this function. If you click Disable, this function will be closed a

Vigor2920 Series User’s Guide 42Settings and allows you type in IP address manually. WAN IP Alias - If you have multiple public IP addresses and woul

Vigor2920 Series User’s Guide 43DDeettaaiillss PPaaggee ffoorr PPPPTTPP//LL22TTPP iinn WWAANN11//WWAANN22 To use PPTP/L2TP as the accessing pro

Vigor2920 Series User’s Guide 44 WAN IP Alias - If you have multiple public IP addresses and would like to utilize them on the WAN interface, please

Vigor2920 Series User’s Guide 45 Enable / Disable Click Enable for activating this function. If you click Disable, this function will be closed and a

Vigor2920 Series User’s Guide 46After finishing all the settings here, please click OK to activate them. 33..11..44 LLooaadd--BBaallaannccee PPooll

Vigor2920 Series User’s Guide 47Click Index 1 to access into the following page for configuring load-balance policy. Enable Check this box to enable

Vigor2920 Series User’s Guide vi

Vigor2920 Series User’s Guide 4833..22 LLAANN Local Area Network (LAN) is a group of subnets regulated and ruled by router. The design of network s

Vigor2920 Series User’s Guide 49 WWhhaatt iiss RRoouuttiinngg IInnffoorrmmaattiioonn PPrroottooccooll ((RRIIPP)) Vigor router will exchange rou

Vigor2920 Series User’s Guide 50Disable. 2nd IP Address Type in secondary IP address for connecting to a subnet. (Default: 192.168.2.1/ 24) 2nd Subne

Vigor2920 Series User’s Guide 51the 1st subnet with neighboring routers. 2nd Subnet - Select the router to change the RIP information of the 2nd subn

Vigor2920 Series User’s Guide 52one DNS Server. If your ISP does not provide it, the router will automatically apply default secondary DNS Server IP

Vigor2920 Series User’s Guide 5333..33..11 PPoorrtt RReeddiirreeccttiioonn Port Redirection is usually set up for server related service inside th

Vigor2920 Series User’s Guide 54 Enable Check this box to enable such port redirection setting. Mode Two options (Single and Range) are provided here

Vigor2920 Series User’s Guide 5533..33..22 DDMMZZ HHoosstt As mentioned above, Port Redirection can redirect incoming TCP/UDP or other traffic on

Vigor2920 Series User’s Guide 56DMZ Host for WAN2 and WAN3 is slightly different with WAN1. See the following figure. If you previously have set up

Vigor2920 Series User’s Guide 57 33..33..33 OOppeenn PPoorrttss Open Ports allows you to open a range of ports for the traffic of special applica

Vigor2920 Series User’s Guide viiTTaabbllee ooff CCoonntteennttss 1 Preface ...

Vigor2920 Series User’s Guide 58 Enable Open Ports Check to enable this entry. Comment Make a name for the defined network application/service. WAN I

Vigor2920 Series User’s Guide 5933..44 AApppplliiccaattiioonnss Below shows the menu items for Applications. 33..44..11 DDyynnaammiicc DDNNSS

Vigor2920 Series User’s Guide 60Domain Name Display the domain name that you set on the setting page of DDNS setup. Active Display if this account is

Vigor2920 Series User’s Guide 61Use the drop down list to choose the desired domain. Login Name Type in the login name that you set for applying doma

Vigor2920 Series User’s Guide 6233..44..22 UUPPnnPP The UPnP (Universal Plug and Play) protocol is supported to bring to network connected devices

Vigor2920 Series User’s Guide 63The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Enabling firewall appl

Vigor2920 Series User’s Guide 64very similar to a URL so some may call it “SIP URL”. SIP supports peer-to-peer direct calling and also calling via a

Vigor2920 Series User’s Guide 65available bandwidth, but Vigor V models also equip with automatic QoS assurance. QoS Assurance assists to assign hi

Vigor2920 Series User’s Guide 662. Even no voice prompt, but the RTP traffic is still secured until the call ends. Note: If the incoming or outgoing

Vigor2920 Series User’s Guide 67SIP URL Enter your friend’s SIP Address. Dial Out Account Choose one of the SIP accounts for this profile to dial o

Vigor2920 Series User’s Guide viii3.4 Applications...

Vigor2920 Series User’s Guide 68DDiiggiitt MMaapp For the convenience of user, this page allows users to edit prefix number for the SIP account wit

Vigor2920 Series User’s Guide 69OP Number The front number you type here is the first part of the account number that you want to execute special fu

Vigor2920 Series User’s Guide 70Enable Click this to enable this entry. Call Direction Determine the direction for the phone call, IN – incoming ca

Vigor2920 Series User’s Guide 71For Block IP Address – this function can block incoming calls (through Phone port) coming from IP address. Such contr

Vigor2920 Series User’s Guide 72Call Forward [All][Act] Dial the number typed in this field to forward all the incoming calls to the specified place

Vigor2920 Series User’s Guide 73PPSSTTNN SSeettuupp Some emergency phone (e.g., 911) or special phone cannot be dialed out by using VoIP and can be

Vigor2920 Series User’s Guide 7433..55..22 SSIIPP AAccccoouunnttss In this section, you set up your own SIP settings. When you apply for an accoun

Vigor2920 Series User’s Guide 75lines with numbers (30 – 39) offered for ISDN-S0. You can specify any one of them as ring port for specified SIP acco

Vigor2920 Series User’s Guide 76The system will select a proper way for your VoIP call. SIP Port Set the port number for sending/receiving SIP mess

Vigor2920 Series User’s Guide 77Ring Pattern Choose a ring tone type for the VoIP phone call. Prefer Codec Select one of five codecs as the defaul

Vigor2920 Series User’s Guide ix4.3.3 Open Ports...

Vigor2920 Series User’s Guide 7833..55..33 PPhhoonnee SSeettttiinnggss This page allows user to set phone settings for Phone 1 and Phone 2 respect

Vigor2920 Series User’s Guide 79down list to choose any one of them.

Vigor2920 Series User’s Guide 80DDeettaaiilleedd SSeettttiinnggss ffoorr PPhhoonnee PPoorrtt Click the number link for Phone port, you can acces

Vigor2920 Series User’s Guide 81Index (1-60) in Phone Book - Enter the index of phone book profiles. Refer to section DialPlan – Phone Book for detai

Vigor2920 Series User’s Guide 82Defined and fill out the corresponding values for dial tone, ringing tone, busy tone, congestion tone by yourself for

Vigor2920 Series User’s Guide 83the default value was 101. This setting is available for the OutBand (RFC2833) mode. 33..55..44 SSttaattuuss Fr

Vigor2920 Series User’s Guide 84Tx Pkts Total number of transmitted voice packets during this connection session. Rx Pkts Total number of received

Vigor2920 Series User’s Guide 85 SSeeccuurriittyy OOvveerrvviieeww Real-time Hardware Encryption: Vigor Router is equipped with a hardware AES encr

Vigor2920 Series User’s Guide 8633..66..22 GGeenneerraall SSeettuupp By clicking the General Settings, a new web page will appear so that you coul

Vigor2920 Series User’s Guide 87 Packet-OVERDRIVE This feature can enhance the performance in data transmission about 40%* more (by checking Tx Bur