Draytek VigorAP 700 Bedienungsanleitung

VViiggoorrAAPP 770000 WWiirreelleessss AAcccceessss PPooiinntt User’s Manual Version 1.0 Date: 2009/1/07

4 1-4 Familiar with your new VigorAP 700 Front Panel LED Status Description On The device is powered on. PWR Off The device is powered off. On

5 Back Panel Interface Description Antennas Two reserve SMA antenna connectors for screwing 3dBi detachable antennas enclosed with the product. PWR

6 This page is left blank.

7 Chapter II: System and Network Setup 2-1 Installing VigorAP 700 to your Network Please follow the following instruction to build the network connect

8 2-2 Connecting to VigorAP 700 by Using Web Browser After the network connection is built, the next step you should do is setup the access point with

9 2. Select Specify an IP address, then input the following settings in respective field and click OK when finish. IP address: 192.168.1.9 Subnet Mas

10 2-2-2 Windows 2000 IP address setup 1. Click Start button (it should be located at lower-left corner of your computer), then click control panel.

11 2-2-3 Windows XP IP address setup 1. Click Start button (it should be located at lower-left corner of your computer), then click control panel. Do

12 2-2-4 Windows Vista IP address setup 1. Click Start button (it should be located at lower-left corner of your computer), then click control panel.

13 2-2-5 Connecting to Web Management Interface All functions and settings of this access point must be configured via web management interface. Pleas

COPYRIGHT Copyright ©2008/2009 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored i

14 NOTE: If you can’t see the web management interface, and you’re prompted to input user name and password again, it means you don’t input username a

15 Here are descriptions of every item: System Uptime Displays the total passed time since the VigorAP 700 is powered. Hardware Version Displays har

16 2-4 Select an Operating Mode for Wireless Access Point This access point can be operated in different modes; you can click Basic Setting on the lef

17 to accept wireless clients while the access point is working as a wireless bridge. Universal Repeater This product can act as a wireless range ext

18 and 802.11g band will be able to connect to this access point. If you want to allow 802.11b, 802.11g, and 802.11 n clients to connect to this acc

19 2-4-1-1 Multiple SSID This access point supports four SSIDs. Except the main SSID (it can be configured in Basic Setting page), you can configure a

20 kinds of data, to give higher priority to applications which require instant responding. Therefore you can improve the performance of such network

21 If you want to allow 802.11b, 802.11g, and 802.11n clients to connect to this access point, select 2.4GHz (B+G+N). Main SSID Please input the SSID

22 Here are descriptions of every setup item: Select Click the radio button to select the access point. Channel Display the channel number of the a

23 2-4-3 AP Bridge-Point to Point Mode In this mode, this VigorAP 700 will connect to another VigorAP 700 which uses the same mode, and all wired Eth

FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided betwee

24 MAC address 1 Please input the MAC address of the VigorAP 700 you wish to connect. After you finish with setting, please click Apply, and the fol

25 2-4-4 AP Bridge-Point to Multi-Point Mode In this mode, this VigorAP 700 will connect to up to four VigorAP 700s which uses the same mode, and all

26 connect. After you finish with setting, please click Apply, and the following screen will be displayed: When you see this message, the settings y

27 Here are descriptions of every setup item: Band Please select the wireless band you wish to use. By selecting different band setting, you’ll be ab

28 After you finish with setting, please click Apply, and the following screen will be displayed: When you see this message, the settings you made is

29 If you select 2.4GHz (B), 2.4GHz (N), or 2.4GHz (G), only wireless clients using the wireless band you select (802.11b, 802.11n, or 802.11g) will b

30 After you finish with setting, please click Apply, and the following screen will be displayed: When you see this message, the settings you made i

31 Here are descriptions of every setup item: Enable WPS Check this box to enable or disable WPS function. Wi-Fi Protected Setup Information All inf

32 will be replaced by asterisk for security reason. If encryption is not set on this access point, nothing will be displayed here. Device Configurati

33 2-6 Advanced Wireless Settings This VigorAP 700 has many advanced wireless features. Please note that all settings listed here are for experienced

EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France, Germa

34 Data Rate Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper

35 When you see this message, the settings you made is successfully save. You can click Continue to return to previous page and continue on other se

36 Note: If you have enabled Multiple SSID function, please select the SSID network you wish to configure in advance. Please remember it’s very impor

37 2-7-1 Disable Security Select the SSID you wish to configure. When you select Disable, wireless encryption for the network is disabled. After you

38 Here are descriptions of every setup item: Key Length There are two types of WEP key length: 64-bit and 128-bit. Using 128-bit is safer than 64-b

39 Authentication Section 2-7-5 for detailed instructions. After you finish with setting, please click Apply, and the following screen will be displa

40 After you finish with setting, please click Apply, and the following screen will be displayed: When you see this message, the settings you made is

41 address RADIUS Server Port Please input the port number of RADIUS authentication server here. Default value is 1812. RADIUS Server Password Please

42 After you finish with setting, please click Apply, and the following screen will be displayed: When you see this message, the settings you made i

43 2-8 Radius Server Comparing to other wireless security measures, radius server provides user-based authentication. If your wireless client supports

Table of Content Chapter I: Product Information ...1 1-1 Introduction ...

44 button to add the user to radius server database. You can click Cancel to clear the text you typed in above three fields. All current radius users

45 2-9 MAC Filtering Another security measure you can use to keep hackers and intruders away is MAC filtering. You can pre-define a so-called ‘white-l

46 a to f here, like 112233445566 or aabbccddeeff. Comment You can input any text here as the comment of this MAC address, like ROOM 2A Computer or a

47 2-10 System Utilities This access point provides some control functions include password, IP address management, and DHCP server function. Please c

48 2-10-2 IP Address of the Wireless Access Point You can change the IP address of this VigorAP 700 to make it becoming one part of your local network

49 2-10-3 DHCP Server This VigorAP 700 is capable to act as a DHCP server for your network. It is disabled by default. If you want to activate this fu

50 When you see this message, the settings you made is successfully save. You can click Continue to return to previous page and continue on other set

51 2-11 Configuration Backup and Restore You can backup all configurations of this access point to a file, so you can make several copied of access po

52 2-12 Firmware Upgrade If there is new firmware of this VigorAP 700 available, you can upload the firmware to the access point to change the firmwar

53 2-13 Restart When you think the access point is not working properly, you can use this function to restart the access point. This may help and solv

2-11 Configuration Backup and Restore ... 51 2-12 Firmware Upgrade ...

54 This page is left blank.

55 Chapter III: Troubleshooting If you found the access point is working improperly or stops responding to you, don’t panic! Before you contact your d

56 powered. I can’t locate my access point by my wireless client a. Check if Broadcast SSID is set to off. b. Is Antenna properly installed and sec

57 Appendix: Glossary Default Gateway (Access point): Every non-access point IP device needs to configure a default gateway’s IP address. When the dev

58 11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as “x” number of leading 1 is. When both are r

59 Application Protocol Port Number Telnet TCP 23 FTP TCP 21 SMTP TCP 25 POP3 TCP 110 H.323 TCP 1720 SNMP UCP 161 SNMP Trap UDP 162 HTTP TCP

1 Chapter I: Product Information 1-1 Introduction Thank you for purchasing this VigorAP 700! With this high cost-efficiency VigorAP 700, computers and

2 1-2 Safety Information In order to keep the safety of users and your properties, please follow the following safety instructions: z This access poi

3 1-3 Package Contents Before you starting to use this access point, please check if there’s anything missing in the package, and contact your dealer